Ask Linda

Linda Lee
Ask Linda

Linda Lee, our Q&A expert, welcomes your questions. Direct your e-mails to her at sewnews@sewnews.com.

Bias Opinion

Is there a trick to sewing bias tape around curves without it twisting and cupping?

Audrey

There are some very fancy bias binder attachments available for most machines. These attach and stitch bias tape to an edge in one step, but there's a better way that doesn't require any special equipment. For the best finished look, choose a double or French bias tape or cut your own bias pieces to customize the color and vary the size.

Cut bias strips six times your preferred finished width, plus an additional 1/8*-1/4* depending on the fabric thickness. The thicker the fabric, the more you should add to the width. Fold the strip in half lengthwise before applying it to the edge. Pin the raw binding edges to the project raw edge. As you're working around the curve, give the binding a little shove, easing as much fullness into the application as you can without creating puckers. This will keep the binding flat when finished.

Stitch the binding to the project along the seamline. Trim the seam allowance to an even width that's slightly narrower than the finished binding width. Wrap the binding around the raw edges, keeping it as snug as possible against the edge. The outer folded edge should lie beyond the seamline on the project wrong side. Pin frequently in the seam well, parallel to the outer edge. Stitch in the ditch from the right side so that the stitches are both hidden in the seam well and catching the folded edge on the fabric wrong side.

Suited for Silk

What kind of lining should I use in a silk suit?

Carolyn

The best all-purpose lining for most projects and fabrics is Bemberg rayon. You can find this in most independent fabric stores or online. It's lightweight but durable. I also recommend using China silk for a very lightweight lining, although it's less durable and can shred at stress points over time. Avoid using polyester lining in a silk garment. It's too stiff and doesn't conform to the characteristics of a nice silk.

Ruffle Trouble

I'm covering seat cushions for my kitchen chairs. How do I calculate the amount of fabric needed for a ruffle around each cushion?

Michael

First, decide whether you want a single-layer ruffle that's hemmed on one edge or if you want a ruffled that's folded in half, so the fabric right side is visible on both sides. Either way, measure the circumference of the seam cushion. Multiply that measurement by at least two and add a few inches. Most ruffles are double the fullness. Next, calculate the desired width of the ruffle and decide whether the ruffle will be single or double-sided. Cut enough strips to stitch together and form one long piece.

For the Beads

Which presser foot should I use to attach beads?

Anonymous

Look for a presser foot that has a scooped out tunnel on the foot bottom that's large enough to travel over the beads. Manufacturers have different names for these feet but look for a "pearls and piping" or "beading" foot. You'll also want to purchase invisible tread to use on the

top of the machine with regular thread in the bobbin. If your beads are strung on poor quality cotton thread and you want durability, consider restringing the beads on nylon beading thread.

Place the string of beads on the fabric surface and fit the presser foot over the beads. Set your machine to a lengthened zigzag stitch, so it traverses over the beads easily. Stitch slowly and use the needle down capability on your machine so it's easy to adjust the beads and stitching frequently.

 

GOT A QUESTION?

Send it to: Sewing Q&A, Sew News, 741 Corporate Circle, Ste. A, Golden, CO 80401 or sewnews@sewnews.com. While we can’t answer every question personally, those of general interest will be published in the magazine. For answers to other sewing questions, visit us at sewnews.com.

 

Appeared in:

Post a comment
To comment on this article you must be logged in. Not a member?

USER COMMENTS

polyester rugs
I'm looking for a pattern or someone who knows how to make polyester rugs. I know you cut two inch squares and then fold them into a triangle then sew. I don't know how to construct it after that. I think these rugs date back about twenty years ago. Thank-You Lynn
Pants for Handicapped
I'm looking for a resource too - in the meantime, try using a pull-on or side close pattern and insert hidden zippers (or other fasteners) in both side seams from the waist to the lower hip - going an inch or so below the inseam level will allow even more give when the fasteners are open.
Pattern Adjustment for Curved Back Mom
View a dowager's hump as a semi-deflated basketball- you need to make a sort of "fan out” to cover, making curving the back center seams outward starting just below the lower armhole level. Curve each center back 1.5-5" gently. You may need to use long darts from below the waist upward to the widest part of the hump to allow for the curve widening the side seams accordingly. Also cut the back 3-5" longer at lower edge depending on the severity of the spine curvature you're covering, then fit & trim. You need to supply extra length for the back from the mid-back up to the neck. Armholes may also have to be cut wider from two inches down from shoulder to the bottom of the armhole, but not wider at the very bottom of the armhole. Try using a muslin to make a fitting shell, and then you'll have a guide for future garments. Good for you to try this tough challenge. Your Mum should be delighted. If this isn’t clear, ask away!
Cutting out stretchy and or slippery fabric
It seems so difficult to cut out fabric with spandex in it. It is hard to lay it flat, match selvedge, and keep grain right. Are there any tricks I could use? How do industry cutters do it? It seems to come off the bolt tweeked and out of the dryer twisted. Also slippery slinky fabric seems to be a nightmare to cut out. It falls off the table and slips around. Help. Sincerely, frustrated stretchy and slippery fabric cutter.
Pattern Adjustment for Curved Back Mom
Mom 96 yrs old has a very bad curve in her back, how do I ajust a pattern to allow her to look her best.
Handicapped Patterns, Resource?
Mom is in a wheelchair now and I need a pants pattern which allows easy removal of garments in order to help when she's incontinent. Any suggestions?

Login:

Forgot password?
 
© F+W All rights reserved.