Common Serger Feet & How to Use Them

A serger isn’t just for finishing raw edges. Learn about useful serger presser feet that take your sewing to the next level and help you take full advantage of everything your serger can do. Note: The featured serger feet imagery are for Janome sergers.

Blind Hem Foo

Blind Hem Serger Foot Common Serger Feet & How to Use Them

Use a blind hem foot to create an invisible hem on a garment or home-décor project.

Fold the fabric toward the wrong side to the desired hem width. Fold the fabric with right sides together, exposing a scant 1⁄2” of the raw edge. Position the fabric wrong side up beneath the foot.

Select a 2- or 3-thread narrow hem stitch on the machine. Slowly lower the needle into the fabric to check the needle placement. The left needle should barely graze the hem, catching one or two fibers. The foot-edge guide should be flush with the fabric fold. With the knife blade up, serge the hem, making sure to only cut off the fabric raw edge, catching the fold within the stitching. Press open the seam.

Gathering Foot

Gathering serger foot Common Serger Feet & How to Use Them

The gathering foot finishes a seam and attaches a ruffle in one step. For best results, use lightweight fabric, such as cotton. Heavyweight fabric, such as denim, produces fewer ruffles. Cut the fabric to be gathered (lower fabric) longer than the upper fabric (2:1 ratio).

Select a 4-thread overlock stitch on the machine. Raise the presser foot. Position the lower fabric under the foot just below the needle. Position the upper fabric between the guide over the lower fabric. Lower the presser foot.

Slowly turn the hand wheel toward you to stitch the first three or four stitches to help the machine catch the fabric without jamming; stitch. While stitching, hold one fabric in each hand to evenly guide it through the machine. Don’t apply pressure to the lower fabric, as this prevents gathers from forming. Hold the upper fabric taut. Adjust the gather size by changing the stitch length between 2mm and 5mm.

Remove the fabric from the machine; press open the seam.

Beading Foot

Beading serger foot Common Serger Feet & How to Use Them

Use the beading foot to attach a strand of beads directly to fabric to create a decorative hemline or an easy embellishment. The stitch selection varies according to machine brand. Check with the machine manual and foot instructions to select the proper stitch type.

Pull the string of beads along the foot guide toward the back. Extend the bead string at least 1cm past the fabric edge to ensure the machine catches both the beads and fabric.

The stitch length should be the size of the bead diameter. For example, if using 3mm beads, select a 3mm stitch length.

Some machines recommend folding the fabric with wrong sides together and aligning the beads along the folded edge before stitching.

Position the folded edge along the foot edge; stitch. With this method, the raw edge won’t be finished. Or keep the serger knife in the up position while stitching a 3-thread rolled hem to ensure that the edge is finished simultaneously as the beads are stitched.

Piping & Cording Foot

Piping Cording Foot 2 Common Serger Feet & How to Use Them

Piping Cording Foot 1 Common Serger Feet & How to Use Them

Insert a professional-looking piped edge into a garment or accessory quickly and easily using the piping/cording foot. Note that for some makes and models, such as those shown here, these are separate feet.

Select a 3mm-long 3-thread overlock stitch.

Sandwich the piping tape between two fabric pieces with right sides together, aligning the raw edges. Position the fabric sandwich under the presser foot, aligning the piping within the foot groove.

Stitch, and then turn the fabric to the right side; press.

Or stitch piping to the center of fabric by disengaging the knife and selecting a chain stitch.

Elastic Foot

Elastic Serger Foot Common Serger Feet & How to Use Them

Easily stitch elastic to a fabric edge using an elastic foot. Adjust the pressure on the elastic as you stitch to create the desired amount of ruffles. The foot also slightly stretches the elastic as you stitch, preventing pulling and tugging on the needles.

Select a 3- or 4-thread overlock stitch on the machine. Adjust the foot tension by turning the dial at the foot toe. Tightening the screw adds pressure, causing the elastic to stretch more, increasing the gathering.

Insert the elastic into the guide on the foot so that the elastic right-side edge aligns with the guide. Turn the guide knob so it abuts the elastic left-side edge.

Carefully turn the hand wheel toward you to take a few stitches. Once the elastic and fabric are feeding smoothly, stitch at medium speed.

Janome of America sponsors this series and provided serger feet and the AT 2000D serger.


 Common Serger Feet & How to Use Them
This entry was posted in Tips & Techniques and tagged . Bookmark the permalink.

3 Responses to Common Serger Feet & How to Use Them

  1. Barbara Joy says:

    Hi! Someone recommended the Sew It All Videos, but I cannot find them on the site, are they on another server/YouTube, etc? I am looking for the best in tutorial sewing videos, sergers/sewing machines, etc. for apparel. TV shows, specials, etc. if you can help. Thank you very much!

  2. Brenda Bush says:

    This is great. Do you have one for Babylock feet?